毕业论文

打赏
当前位置: 毕业论文 > 化学论文 >

磷酸锂催化剂制备方法研究及应用

时间:2021-06-18 20:06来源:毕业论文
采用不同浓度原料 液与不同反应温度制备磷酸锂催化剂,研究制备条件对催化剂催化性能和表面性 能的影响,评价所制备催化剂的催化性能。通过气相色谱、X 射线衍射、比表面 积分析

摘要磷酸锂作为环氧丙烷异构化为烯丙醇的高效催化剂,本文采用不同浓度原料 液与不同反应温度制备磷酸锂催化剂,研究制备条件对催化剂催化性能和表面性 能的影响,评价所制备催化剂的催化性能。通过气相色谱、X 射线衍射、比表面 积分析对所制备的催化剂进行了表征,发现改变反应条件制备的催化剂得到的是 中孔结构的磷酸锂微球,孔结构很不规整,比表面积不大,并且其催化性能随原 料液浓度的降低有所提高,随反应温度的变化没有规律,在反应物都为 0.1mol, 加水量为 275ml,反应温度为 65℃时其催化性能最佳。68562

毕业论文关键词 磷酸锂 烯丙醇 环氧丙烷异构化

Title The preparation method and application of lithium phosphate catalyst

 

 

Abstract

Lithium phosphate is used as a highly efficient catalyst for propylene oxide isomerization to allyl alcohol. In this report, lithium phosphate catalysts were prepared by using different concentrations of materials and reaction temperatures. The impact of preparation conditions on the catalytic properties and surface properties were studied, the catalytic properties was therefore evaluated. The prepared catalysts were characterized through the analysis of gas chromatography, X-ray diffraction and BET. It was found that catalysts obtained by changing the reaction conditions were hollow structure, the pore structure was very neat with small BET surface area. In addition, its catalytic performance improved with the decrease of material concentration but showed random change at different reaction temperatures.It was shown that the optimal catalytic performance was achieved when the reactants were 0.1moland added water to 275ml with reaction temperature at 65 ℃.

 

 

 

Keywords: Lithium phosphate Allyl alcohol Isomerization Propylene oxide

 

1 绪论 1

1.1 环氧丙烷异构化 1

1.1.1 异构化简介 1

1.1.2 环氧丙烷异构化 1

1.2 磷酸锂的概况 1

1.3 催化剂的制备方法 2

1.3.1 浸渍法 2

1.3.3 混合法和熔融法 3

1.3.4 微乳液法 3

1.3.5 化合键合法 3

1.3.6 纤维化法 3

1.4 国内外研究发展 4

1.4.1 国内研究进展 4

1.4.2 国外研究进展 5

1.5 本文的研究背景及意义 5

2 磷酸锂催化剂的制备与表征 5

2.1 本实验仪器及原料 5

2.1.1 实验试剂 5

磷酸锂催化剂制备方法研究及应用:http://www.youerw.com/huaxue/lunwen_77147.html
------分隔线----------------------------
推荐内容