毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

防盗窗用智能光电探测及AT89S52单片机智能研究+电路图+C程序

时间:2019-10-05 20:52来源:毕业论文
由AT89S52单片机构成的单片机系统作为核心,结合红外传感器、光报警显示电路和GSM短信模块共同组成。红外传感器采用光探测器为核心部件,在发出红外线遭到障碍物阻挡后,发送信号

摘要本文查阅和研究了家居防盗报警系统的研究背景和现状,在此基础上设计了一种红外光电探测和单片机智能控制为核心的家居防盗窗报警系统,并设计了系统硬件电路和软件程序。
本系统由AT89S52单片机构成的单片机系统作为核心,结合红外传感器、光报警显示电路和GSM短信模块共同组成。红外传感器采用光探测器为核心部件,在发出红外线遭到障碍物阻挡后,发送信号给单片机,单片机进行信号处理后,光报警电路发出报警信号,同时单片机通过GSM短信模块将警情发送到保安人员和业主手中。18926
本系统采用模块化结构设计,利用集成电路系统和外部按键人机交互工程,软件采用C语言编程,稳定性好,能够可靠工作,并且成本低、安装便捷、可操作性强,能够实现智能防盗报警的目标。
关键词:家居防盗报警系统  红外传感器  光电探测  单片机  智能控制
毕业设计说明书(毕业论文)外文摘要
Title  Intelligent photoelectric detection and intelligent control of the microcontroller for security windows.
Abstract
This article inspect and research the background and status of the home burglar alarm system, on the basis of which designed an infrared detection and intelligent control of SCM as the core of home burglar alarm system about security window and designed the hardware circuit and software programs of the system..
The system consists of a SCM system which is formed by a single-chip microcontroller AT89S52 system as the core, combined with infrared sensors, optical alarm display circuit and GSM SMS module. The infrared sensor uses light detector as the core components, after the issued infrared was obstruction, sends a signal to the microcontroller. After the microcontroller processes the signal, the light alarm circuit sends a alarm signal, at the same time the microcontroller sends alarm messages to security personnel and the owner’ hands via the GSM module.
The system used a modular design and integrated systems and external key human-computer interaction engineering, using C programming language, which has good stability, reliable operation, low cost, convenient installation and easy operation, can achieve the goal of intelligent burglar alarm.
Keywords: home burglar alarm system  infrared sensor  photoelectric detection  SCM  intelligent control
目次
1  引言    1
1.1    研究与设计背景    1
1.2    小区环境分析    1
1.3    家居防盗报警器发展概况及存在的不足    1
2  系统整体方案设计    2
2.1    系统整体方案结构和功能    2
2.2    光电信号探测模块设计    3
2.2.1    传感器的选择    3
2.2.1.1    红外传感器的简介及其种类    3
2.2.1.2    红外传感器的工作机理及特点    4
2.2.1.3    红外传感器的结构    5
2.2.1.4    红外传感器的性能指标    7
2.2.2    红外传感器控制电路元件选择    8
2.2.3    显示模块的选择    9
2.2.3.1    数码管显示设备的选择    9
2.2.3.2    发光二极管的选择    10
3  系统硬件电路设计    11
3.1    单片机系统电路设计    11
3.1.1    单片机结构及引脚功能特点    11
3.1.2    时钟电路设计    14 防盗窗用智能光电探测及AT89S52单片机智能研究+电路图+C程序:http://www.youerw.com/zidonghua/lunwen_40241.html
------分隔线----------------------------
推荐内容