毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

某塑料制品厂总配电所(高压配电所带-车间变电所)及高压配电系统设计

时间:2019-10-01 14:30来源:毕业论文
负荷计算机无功补偿;总降压变电所的所址和型式;确定总降压变电所的主接线方案;短路计算,并选择一次设备;选择电源进线及高压配电方案;选择电源进线的二次回路方案,并整

摘要   本设计题目为“某塑料制品厂总配电所(高压配电所带-车间变电所)及高压配电系统设计”,设计内容:负荷计算机无功补偿;总降压变电所的所址和型式;确定总降压变电所的主接线方案;短路计算,并选择一次设备;选择电源进线及高压配电方案;选择电源进线的二次回路方案,并整定继电保护;总降压变电所防雷保护及接地设计;总降压变电所主接线图;总降压变电所平面图与接地装置布置图。完成设计图:主接线,平面布局和防雷保护共三幅。本次所有设计均参照工业与民用供配电设计手册,所有计算结果与绘制图纸均符合国家颁布相关电气设计规范。19012
关键词  负荷与短路计算  高压设备选择  继电保护整定计算  主接线图  平面布置图
毕业设计说明书(毕业论文)外文摘要
Title  The Design Of 10kV Substation         
Abstract
The title of this design is the whole plant distribution substation and power distribution system design of a plastic products factory。The design includes that the load calculation of the factory ,works out the compensation computing power,make sure the best site of the Substation and main distribution lines for enterprises,the short circuit current calculation of the high pressure side and low pressure side then make the main equipment selection,and validation,the main equipment relay protection design, lightning protection and grounding design.the design includes three pictures that the main connection diagram about the total distribution substation and power distribution system and lightning protection。All the design according to the relevant provisions of the national electricity sector.
Keywords  load calculation and short circuit current calculation  the equipment of high pressure selection  relay protection setting  the main wiring map  the design map of plan
目   录  
1  引言1
2  负荷计算和无功功率补偿2
2.1  负荷计算 2
2.1.1  车间和工厂计算负荷的确定 2
2.2  无功功率补偿及计算 4
2.2.1  工厂负荷计算与无功功率补偿计算5
2.2.2  电容器的选择5
2.2.3  补偿后电流5
2.3  尖峰电流的计算5
3  变电所与变压器的选择7
3.1  变配电所所址的选择7
3.2  变配电所型式的选择7
3.3  变电所变压器台数和容量的选择7
3.3.1  变压器型式7
3.3.2  变压器台数的选择7
3.3.3  变压器容量的选择9
4  变电所主接线方案的设计10
4.1  变电所主接线方案的设计10
4.2  母线接线方式10
5  短路计算及一次设备的选择11
5.1  短路计算11
5.1.1  变压器阻抗11
5.1.2  导线的选取11
5.2  短路计算12
5.3  一次设备的选择与校验14
5.3.1  按正常条件选择14
5.3.2  按短路条件校验14
6  继电保护与二次回路20
6.1  继电保护20
6.1.1  线路的保护 20
6.1.1.1  高压进线的保护 20
 
6.1.1.2  车间变电所进线保护21
6.1.2  电力变压器的保护23
6.1.3  10KV电力电容器的保护 26
6.1.4  接地保护28
6.2  二次回路的选择29
6.2.1  自动重合闸装置的选择 29
6.2.2  绝缘监察装置与测量仪表29
7  防雷保护和接地装置的设计32
7.1  防雷保护32
7.1.1  防雷装置的选择32
7.2  接地 33
结论34
致谢35
参考文献36
图1  工厂平面图38 某塑料制品厂总配电所(高压配电所带-车间变电所)及高压配电系统设计:http://www.youerw.com/zidonghua/lunwen_40185.html
------分隔线----------------------------
推荐内容