毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

稀氨水吸收器的设计+CAD图纸+答辩PPT

时间:2018-05-28 21:46来源:毕业论文
采用固定管板式换热器结构。该设备适用于温差不大,壳程流体清洁,不易结垢拆卸、清洗的场合。在设计过程中,依照GB151-1999《钢制管壳式换热器》对换热器依次进行工艺计算、结构

摘要:换热器是许多工业部门广泛应用的工艺设备。设计中考虑操作条件及介质的特性,本设计采用固定管板式换热器结构。该设备适用于温差不大,壳程流体清洁,不易结垢拆卸、清洗的场合。在设计过程中,依照GB151-1999《钢制管壳式换热器》对换热器依次进行工艺计算、结构设计(材料选型)、强度计算,最后完成专题讨论。其中在强度计算中,根据温差具体的数值,对膨胀节的需要进行计算。本设计每层管子排列方式采用正三角形排列,这种方法在相同的管板面积上可排较多的管子,且管外表面传热系数大。23445
毕业论文关键词:换热器;固定管板;工艺设计;结构设计;强度计算
Design of Dilute Ammonia Heat Exchanger
Abstract:The heat exchanger is the techniques equipment widely used in many industrial departments. In the design it uses the fixed tube plate type of the heat interchanger structure,because of the operating condition and the medium characteristic. This equipment is suitable when the temperature difference is not big,the shell regulation fluid is clean,or the fouling,disassembling or cleaning for the heat exchanger is not easy. In the process of the design,the technological design,the structural design(material shaping) and the strength calculation must according to the GB151-1999"Steel System Shell Type Heat interchanger",finally it completes the seminar. In the strength calculation,it must be computed for the require of the part of inflates according to the difference concrete value ot the temperature.In the design the way of each pipe arrangement uses the equilateral triangle arrangement,this method may arrange many pipes in the same tube plate area,also the tube outside surface heat transfer coefficient is big.
KeyWords: heat exchanger;fixed tube plate;technological design; structural design; strength calculation
目  录
1 绪论    1
1.1换热器的应用及其发展    1
1.1.1 换热器的应用    1
1.1.2 换热器的发展趋势    1
1.2 换热器的分类及其特点    2
1.3 列管式换热器的设计    2
2 换热器热力计算    4
2.1 物性参数计算    4
2.2 热力计算    6
2.2.1确定物性数据    6
2.2.2热量衡算    6
2.2.3 流动空间及流速的测定    7
2.2.4 计算总传热系数    7
2.2.5换热器核算    10
2.3 阻力计算    12
3 换热器的结构设计    14
3.1 筒体设计    14
3.1.1筒体材料的选取    14
3.1.2筒体壁厚的计算    14
3.1.3水压试验    15
3.1.4 结构形式    15
3.2 管箱设计    15
3.2.1管箱材料    16
3.2.2管箱尺寸    16
3.2.3管箱壁厚计算    16
3.2.4水压试验    17
3.3 管箱法兰    17
3.3.1材料的选取    17
3.3.2 结构尺寸    17
3.3.3 结构型式    17
3.4 接管    18
3.4.1材料的选取    18
3.4.2结构尺寸    18
3.4.3 结构型式    24
3.5 接管法兰    24
3.5.1 材料的选取    24
3.5.2 结构尺寸    24
3.5.3 结构型式    25
3.6 垫片    25
3.7 管板    26
3.7.1材料的选取    25
3.7.2结构尺寸    26 稀氨水吸收器的设计+CAD图纸+答辩PPT:http://www.youerw.com/jixie/lunwen_16502.html
------分隔线----------------------------
推荐内容