毕业论文论文范文课程设计实践报告法律论文英语论文教学论文医学论文农学论文艺术论文行政论文管理论文计算机安全
您现在的位置: 毕业论文 >> 论文 >> 正文

PLC散装粒子上料及筛选系统设计+CAD图纸

更新时间:2016-8-27:  来源:毕业论文

PLC散装粒子上料及筛选系统设计 要:散装粒子的上料、筛选及输送是许多工业生产流水线中重要的生产形式。适用于食品、医药、化学工业品等行业。采用储料漏斗间断放料方法是通过储料漏斗阀门的间断启闭,使粒子在筛子上停留的时间均匀,筛选质量大大提高,同时通过流量和筛子振动频率的控制也可以保证生产率。应用PLC控制技术实现的这种方法,不仅可以实现单机手动、自动,也可以方便地实现网络联动。这是现代化生产线的重要组成部分,也是实现生产自动的基础。本文来自优,文'论#文^网,毕业论文 www.youerw.com 加7位QQ324,9114找源文
    本课题是关于一套散装粒子上料及筛选系统设计,该设计包括了斗式提升机、储料漏斗、电磁振动筛选机和PLC控制系统。斗式提升机又包括了料斗尺寸设计、上料提升系统、各主要参数的设计校核等。PLC应用设计包括了硬件选择、输入输出点分配、控制流程图和梯形图。
关键词:散装粒子;上料;筛选;PLC。 文学社学期工作计划
Feeding and screening system design on the bulk particles
Abstract:Bulk particle feeding, screening and conveying is important in many industrial production lines in the form of production. The use of intermittent discharge storage hopper is material storage hopper through the intermittent opening and closing the valve, so that the particle residence time in uniform on the screen, screening quality greatly improved, both through traffic and the sieve vibration frequency can be controlled to ensure productivity.Application of PLC control technology to achieve this approach, not only can stand-alone manual, automatic, you can easily network linkage. This is a modern production line, an important part, is the basis of production automatically.
This issue is about a set of bulk materials on the particle filter system design that includes a bucket elevator, storage hopper, electromagnetic vibrating screening machines and PLC control system. Bucket elevator design also includes a hopper size, improved feeding system, check the main parameters of the design and so on. PLC control system, including hardware selection, input and output point of distribution, flow chart and ladder.
Key Words: Bulk particles; feed; filter; PLC.
目  录
1 绪论 1
1.1 斗式提升机发展趋势 1
1.2 PLC发展现状和未来发展趋势 2
1.2.1 PLC发展现状 2
1.2.2 PLC未来发展的方向 4
1.2.3 整合多种功能,更加开放的一体化PLC 4
2 上料筛选系统方案设计 7
2.1 常用斗式提升机选用及相关计算公式 7
2.1.1 常用斗式提升机的特征和用途 7
2.1.2 斗式提升机功率计算公式 8
2.2 斗式提升机的主要部件 8
2.3 斗式提升机的工作原理 9
3 斗式提升机运行阻力及电动机功率计算及校核 11
3.1 提升功率的确定 11
3.1.1 提升机张力计算 12
3.1.2 驱动轴上的圆周力的计算 13
3.1.3 电动机功率N的计算 13
3.1.4 链条的工作载荷的计算 14
3.2 电动机选择 14
3.3 减速箱选择 14
3.4 驱动轴设计及附件的选择 15
3.4.1 轴的材料及热处理 15
3.4.2 轴的结构设计 15
3.4.3 轴的强度校核计算 16
3.4.4 轴承选用 18
3.4.5 驱动链轮键的设计校核 19
3.4.6 联轴器的选择 19
3.5 驱动链轮的结构设计 20
3.6 头部罩壳的选材及连接 21
3.7 中部区段的设计选材 21
3.8 料斗与环链的设计 21
4 PLC在上料筛选系统中的应用 23
4.1 PLC硬件选用 23
4.2 PLC软件设计 24
5 结论 29
致谢 30
参考文献 31,2885

[1] [2] [3] [4] [5] [6] [7] [8] [9] [10]  ... 下一页  >> 

PLC散装粒子上料及筛选系统设计+CAD图纸下载如图片无法显示或论文不完整,请联系qq752018766
设为首页 | 联系站长 | 友情链接 | 网站地图 |

copyright©youerw.com 优文论文网 严禁转载
如果本毕业论文网损害了您的利益或者侵犯了您的权利,请及时联系,我们一定会及时改正。