毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

SolidWorks试验用手枪枪架设计

时间:2022-01-08 16:51来源:毕业论文
设计了一个可以夹持多种手枪、并能在一定程度上模拟人体射击响应的手枪枪架。在开始阶段,本论文提出并设计了两种试验用手枪的设计方案。通过对比分析,确定了最优的设计方案

摘要为了消除由于人为因素给结果带来的误差,提高射击时的试验安全性等问题,本论文设计了一个可以夹持多种手枪、并能在一定程度上模拟人体射击响应的手枪枪架。在开始阶段,本论文提出并设计了两种试验用手枪的设计方案。通过对比分析,确定了最优的设计方案。经过查阅资料,学到了相关的知识。然后对扭簧、螺栓、推力球轴承及深沟球轴承等零件进行了详细的分析计算及强度校核,并用SolidWorks软件绘制了各零件的三维图,最后画出了手枪架整体的装配图。76816

毕业论文关键字  枪架 扭簧 夹紧 后坐力 

毕业设计说明书外文摘要

Title  The design of pistol frame in test                 

                                                           

Abstract In order to eliminate the error caused by human factors to the results,improve the test safety and other issues,this thesis designs a pistol frame which can clamp various pistols, and ,to some extent ,simulate the human shooting response。At the beginning of this thesis,two kinds of design scheme of the pistol frame is proposed and designed by the design。Through the comparative analysis, the optimal design scheme is determined。Consulting the data let me learn the relevant knowledge。Then the thesis does the analysis,calculation and strength check of the torsion spring,bolts,thrust ball bearings and deep groove ball bearing parts。Then the thesis draws the three-dimensional drawings of the parts by using SolidWorks software,and finally draws the overall assembly of the pistol frame。

Keywords  pistol frame  torsional spring  clamp  recoil

目 录

1  绪论 1

1。1  研究目的 1

1。2  研究背景 1

1。3  试验用手枪架的特点及应用 1

1。4  国内外发展概况 1

1。5  本论文研究的主要工作 4

2  试验用手枪架的设计方案的确定 5

2。1  试验用手枪架的设计方案A 5

2。2  试验用手枪架的设计方案B 6

2。3  方案A、B分析比较 9

3  试验用手枪架设计 10

3。1  手枪夹具设计 10

3。1。1  内嵌贴合块尺寸大小及形状的确定 10

3。1。2  外部金属板的尺寸大小及形状的确定 11

3。1。3  锁紧杆的设计 11

3。1。4  回转金属板设计 12

3。1。5  手枪夹具整体设计 14

3。2  扭簧设计 14

3。2。1  后坐力的确定 15

3。2。2  扭簧参数的计算 20

3。2。3  扭簧装配 21

3。3  轴承设计 22

3。3。1  推力球轴承设计 SolidWorks试验用手枪枪架设计:http://www.youerw.com/jixie/lunwen_88176.html

------分隔线----------------------------
推荐内容