毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

直线导轨副寿命测控系统设计硬件设计

时间:2018-04-19 15:37来源:毕业论文
针对国内滚动直线导轨副规格,测试对象是宽度为35~65mm的滚动直线导轨副,并且能够满足同时模拟三根导轨的工况跑合,加载部件能够分别控制加载三根被测导轨,根据这些要求设计的

摘要滚动直线导轨副是以滚动摩擦为主的直线导向功能部件,因其具有承载能力强、摩擦系数小、进给速度快、定位精度和重复定位精度高等优点,越来越多被高精度数控机械自动化设备所采用。因而对其寿命测试很有必要性。
本文是针对国内滚动直线导轨副规格,测试对象是宽度为35~65mm的滚动直线导轨副,并且能够满足同时模拟三根导轨的工况跑合,加载部件能够分别控制加载三根被测导轨,根据这些要求设计的滚动直线导轨副寿命测控系统。并介绍了液压加载系统的工作原理,试验台跑合控制系统;还介绍了一些用于监测导轨寿命性能参数变化状况的传感器选型,以及对控制系统的原理电路和硬件选型的介绍等。21434
关键词:  滚动直线导轨副 寿命试验 控制系统 硬件选型
毕业论文设计说明书(论文)外文摘要                                                                      
Title    Design of measurement and control system of linear    guide life test---The hardware system design                                                 
Abstract
The linear guide is a linear guide function part is mainly based on rolling friction, because of its high bearing capacity, small friction coefficient, feed speed, accuracy and repeatability of positioning accuracy, more and more high precision CNC machinery, automation equipment used. The test of the life is very necessary.
This paper is aimed at the domestic linear rolling guide specification, the test object is 35~65mm width of the linear rolling guide, and can meet the simulation of three guide rails condition running, load components can respectively control loading three measured rail, according to the design requirements of the linear guide rail pair lifetime measurement and control system. And introduces the working principle of the hydraulic loading system, test bench running control system; it also introduces some changes for sensor selection condition monitoring of rail life performance parameters, as well as the principle of the circuit and the selection of hardware of the control system is introduced.
Keywords :the linear rolling guide  life test  Control system  the selection of hardware
目录
1绪论    1
1.1滚动直线导轨副的概述    1
1.2滚动直线导轨副的寿命研究现状    1
1.3滚动直线导轨副的发展方向    2
1.4课题研究的意义    3
1.5本文主要内容    3
2 滚动直线导轨副的测试系统分析    4
2.1试验台结构分析    4
2.2加载系统设计分析    5
2.3跑合控制系统设计分析    6
2.4控制系统软件分析    7
3试验台测控系统设计    8
3.1 测试系统总体方案    8
3.2传感器的选型    9
3.2.1压力传感器的选择    9
3.2.2振动传感器的选择    11
3.2.3光电传感器的选择    12
3.3测量信号的采集与处理    13
3.3.1信号采集与处理原理    13 直线导轨副寿命测控系统设计硬件设计:http://www.youerw.com/jixie/lunwen_13634.html
------分隔线----------------------------
推荐内容