毕业论文

打赏
当前位置: 毕业论文 > 材料科学 >

含镁铝合金/镀锌钢CMT电弧熔-钎焊工艺研究

时间:2023-01-12 22:27来源:毕业论文
含镁铝合金/镀锌钢CMT电弧熔-钎焊工艺研究。以用含镁量不同的铝合金1060、5052、5A05和Q235镀锌钢板作为研究对象,并以ER4047(AlSi12)焊丝作为填充金属

摘要本实验是以用含镁量不同的铝合金1060、5052、5A05和Q235镀锌钢板作为研究对象,并以ER4047(AlSi12)焊丝作为填充金属,采用CMT(冷金属过渡焊接技术)进行焊接工艺试验研究,并利用金相显微镜、扫描电镜、能谱分析、拉伸试验等方法研究焊接接头的组织与力学性能,以得到Mg元素对铝合金与镀锌钢板焊接接头组织和接头强度的影响。并且研究了在使用AlSi12焊丝焊接的情况下焊接热输入对5A05铝合金和镀锌钢熔-钎焊接头的影响,确定了和填充材料匹配的最佳焊接工艺参数。经过多次反复的实验,得出在送丝速度为3。9m/min,焊接速度为300mm/min时,所得到的焊接工艺参数是为最佳。在最佳的焊接参数条件下,研究上述3种铝合金与镀锌钢板焊接时,发现5052铝合金的抗拉强度最高。同时,得出镁的存在一定程度上抑制了金属间化合物的成长。87006

毕业论文关键词:CMT;镀锌钢;熔-钎焊;异种金属焊接。

Abstract This experiment is to use different magnesium content of aluminum alloy 1060, 5052, 5 a05 and Q235 galvanized steel as the research object, and with ER4047 (AlSi12) as the filler metal, welding wire CMT (cold metal transition welding technique) is adopted to improve the welding procedure test research, and by using metallographic microscope, scanning electron microscopy (sem), energy spectrum analysis and tensile test methods study of microstructure and mechanical properties of welded joint, in order to get the Mg element for aluminium alloy and galvanized steel welding joint organization and the influence of the joint strength。 And studied in the case of using AlSi12 wire welding welding heat input on 5 A05 aluminum alloy and galvanized steel melt - the influence of the welding and brazing head, determines the optimum welding procedure and filler material matching of parameters。 After repeated experiments, it is concluded that the wire feeding speed 3。9 m/min, the welding speed is 300 mm/min, the resulting welding process parameters for the best。 Under the condition of the optimal welding parameters, the above three kinds of aluminum alloy and galvanized steel plate welding, the highest tensile strength of 5052 aluminium alloy。At the same time, the presence of magnesium partly inhibits the growth of the intermetallic compound。

Keywords: CMT; Galvanized steel; Melting-brazing; Dissimilar metal welding。

目  录

第一章 绪论 1

1。1 研究目的及意义 1

1。2 铝合金与钢的焊接性、焊接原理及方法 1

1。2。1 铝合金与钢的焊接性 1

1。2。2 铝合金与钢的焊接原理 2

1。2。3 铝合金与钢的焊接方法 2

1。3 国内外铝合金与钢焊接的研究现状 3

1。3。1铝/钢压焊 3

1。3。1。1 摩擦焊 3

1。3。1。2 搅拌摩擦焊 3

1。3。1。3 爆炸焊 4

1。3。2 铝/钢钎焊 4

1。3。3 铝/钢的熔钎焊 5

1。4 课题主要研究内容 5

第二章 试验材料、设备和方法 7

2。1 试验材料 7

2。1。1实验母材 7

2。1。2 填充材料 8

2。2 实验设备及装置 含镁铝合金/镀锌钢CMT电弧熔-钎焊工艺研究:http://www.youerw.com/cailiao/lunwen_122958.html

------分隔线----------------------------
推荐内容